PCAN-MicroMod FD Configuration — Historique des versions

The user interface has been revised
Added PCAN-MicroMod FD ECU support
Added Device Parameters
Transmit and Receive Symbols can now be disabled
The name of Functions can now be changed optionally
The definition of the custom board can now be customized with a separate user-specific board type file
Potential errors when loading board types from a file are now detected
The availability of the Polarity property of Digital Inputs has been changed
The information text of the configuration is now also transferred to the module and can be read by it
4 new Statistics values (Status Wake-Pin, Busload-Rx, Busload-Tx and Busload-Total) have been added
3 new Functions (Counter with Reload, Copy Conditional, and PID) have been added
The refresh of the interface when loading configuration projects has been improved
The quick help has been revised

A hardware icon was displayed in the status bar even when no connection was established
When changing the firmware settings, the operation was displayed as failed if the bit rate was changed at the same time

Invalid activation code characters are now recognized before starting the CANopen unlock process

The progress update has been improved for module detection, CANopen unlock, firmware settings change, and configuration transfer
Some other minor UI improvements

A missing template file did not cause a warning output
The Custom Board template files were missing in the setup
Selecting bit rate presets could select the wrong nominal or data bit rates
Graphic errors could sometimes occur when editing signal properties
An Access Violation error was thrown after loading a project file in which the board type was missing and then a board type was selected in the Target Hardware dialog box
An incorrect message box was displayed when attempting to send a configuration to a module that had CANopen or CANopen FD active
The command to unlock a CANopen license might not work and a misleading message was displayed if the Microsoft C++ 2010 redistributable package was not installed

Due to an error in the included PCAN-Basic API, a CAN connection could not be established if the version of the PCAN device driver used was older than 4.2.1

Some sample and template files have been corrected
The reading of the advanced detect information and the configuration data has been improved especially if several modules were connected to the same CAN bus
The board type information was not saved correctly in the MicroMod FD project files
When loading MicroMod FD project files, an incorrect warning was displayed about the bit alignment of variables that were set-up with data type double and aligned in Motorola order
Under certain circumstances, the standard configuration was transferred with incorrectly formatted floating point numbers if the firmware operating mode was changed to PEAK standard
Under certain conditions, the Layout tab page was not active in the Symbols window
After changing the board type of a new or opened configuration, the services could not be opened with the sidebar

The Analog Inputs (16-bit) have been expanded to some information about measurement resolution of the selected range
The default name of Curve Definitions has been changed because the format of these names does not match to all other formats
When an invalid or not supported custom bit rate (e.g. prescaler out of range) is loaded or saved, a new warning message is shown in the Output window
When a configuration is sent with an invalid or not supported custom bit rate, an error message is shown in the Output window and the sending is aborted
Improved text output in the Output window with different colors
Improved handling of Bus-Off errors when trying to re-detect modules
New tooltip window that informs about the supported CAN FD clock frequency was added to the Target Hardware dialog box
Activation and unlocking of the CANopen firmware was added
Switching of the firmware operation mode was added
Statistic values Unique ID 0, 1, 2 and 3 were added
New possibility to set the Module ID to ANY
Some minor improvements

In the Symbols layout view, the tooltip window did not display the correct MSB and LSB values of the corresponding element
A entered Function parameter value was not applied if the mouse was used to select a different parameter value edit field
An active feedback output and the corresponding input inverter of a digital function block were not correctly restored when loading a configuration or when changing to another digital function
In the Connect dialog box and the Target Hardware dialog box the Preset and Bit Rate drop-down lists were not refreshed when the bit rates or presets definition was changed
If the selected hardware did support CAN FD, the Manage Bit Rates command always used the FD bit rates for default selection even if CAN FD was not selected
In the Target Hardware dialog box unsupported bit rate presets could be selected
Error Active/Passive CAN controller states were not displayed for connections using compatible CAN interfaces; instead, the old-style BUSHEAVY indicator was shown
Double-clicking on a variable in the Symbols layout could raise an Access Violation error
Loading of unsupported board types was not handled correctly
Corrected the display name of PCAN-MicroMod FD Analog 1
Removed some memory leaks
Some minor bug fixes

'Direction: Reverse' is set as default when the 'Export into Symbols file' dialog box is used the first time
Floating-point values can be specified for the frequency range of digital outputs instead of Integer values