Configurable temperature measurement module with CAN FD connectivity
The MU-Thermocouple1 CAN FD acquires, pre-processes and transmits temperature measurements via the CAN FD protocol. Equipped with 8 thermocouple connectors, this module is calibrated for measurement range J, K or T depending on the selected version. Temperature readings are available in Celsius, Fahrenheit or Kelvin and can be adjusted using a custom factor and offset. Data transmission is performed in CAN FD or classic CAN.
Configuration of data processing, message transmission and LED display is done via the free Thermocouple FD Configuration software for Windows. The configuration developed on the computer is then loaded into the MU-Thermocouple1 CAN FD via the CAN bus, after which the module operates as a standalone CAN node. Multiple units can be configured independently on the same CAN bus.
Requirements
A PEAK-CAN interface is required for configuration.
- 8 connections for type J, K or T thermocouples
- 4 measurement channels equipped with 2 channels of the same type, galvanically isolated
- Measurement ranges:J: -210 to +1121 °CK: -200 to +1370 °CT: -200 to +400 °C
- J: -210 to +1121 °C
- K: -200 to +1370 °C
- T: -200 to +400 °C
- Measurement accuracy: 0.2% or 1 K
- Accuracy of the reference temperature sensors at an ambient temperature of +25 °C: typically ±0.5 K, maximum ±1.0 K
- Maximum temperature data resolution: 1/16 °C
- Message transmission and configuration via High-Speed CAN (ISO 11898-2):Compliant with the CAN 2.0 A/B and FD specificationsCAN FD data transfer rate (64 bytes max) from 25 kbit/s to 10 Mbit/sCAN transfer rate from 25 kbit/s up to 1 Mbit/sNXP TJA1044GT CAN transceiverGalvanic isolation up to 500 V
- Compliant with the CAN 2.0 A/B and FD specifications
- CAN FD data transfer rate (64 bytes max) from 25 kbit/s to 10 Mbit/s
- CAN transfer rate from 25 kbit/s up to 1 Mbit/s
- NXP TJA1044GT CAN transceiver
- Galvanic isolation up to 500 V
- LEDs for measurement channels and power supply
- Configuration with the "Thermocouple FD Configuration" software for Windows®
- Extruded aluminum housing with flange. DIN rail mounting on request
- Supply voltage: 8 to 30 V
- Extended operating temperature range, from -40 to +85 °C
- MU-Thermocouple1 CAN FD in its aluminum housing
- Mating connector included for the power supply (Phoenix Contact MC1.5/2-STF-3.81 - 1827703)
- Thermocouple FD Configuration software for Windows®
- Manual in PDF format
- A PEAK-CAN interface is required for configuration
Configuration software for MU-Thermocouple1 CAN FD for Windows® 11 (x64/ARM64), 10 (x86/x64).
Easy-to-use tool for updating the firmware of PEAK-System hardware products and CAN and LIN adapters for Windows® 11 (x64/ARM64), 10 (x64).
Configurable temperature measurement module with CAN FD connectivity
The MU-Thermocouple1 CAN FD acquires, pre-processes and transmits temperature measurements via the CAN FD protocol. Equipped with 8 thermocouple connectors, this module is calibrated for measurement range J, K or T depending on the selected version. Temperature readings are available in Celsius, Fahrenheit or Kelvin and can be adjusted using a custom factor and offset. Data transmission is performed in CAN FD or classic CAN.
Configuration of data processing, message transmission and LED display is done via the free Thermocouple FD Configuration software for Windows. The configuration developed on the computer is then loaded into the MU-Thermocouple1 CAN FD via the CAN bus, after which the module operates as a standalone CAN node. Multiple units can be configured independently on the same CAN bus.
Requirements
A PEAK-CAN interface is required for configuration.
