CAN and CAN FD board for PCI Express Mini (PCIe) slots
The PCAN-miniPCIe FD is a CAN expansion board in the PCI Express Mini format. Its compact size makes it an ideal solution for connecting embedded systems to up to 4 CAN or CAN FD networks. Galvanic isolation of up to 300 volts separates the computer side from the CAN side. This board is available in single-, dual-, and quad-channel versions.
The CAN FD (Flexible Data rate) standard stands out above all for its increased bandwidth for data transfer. Up to 64 bytes of payload data (versus 8 previously) can be transmitted at a bit rate of up to 12 Mbit/s. CAN FD ensures backward compatibility with the CAN 2.0 A/B standard, allowing CAN FD nodes to be used on an existing CAN network (though the CAN FD extensions cannot be used in this case).
The PCAN-View display software and the PCAN-Basic programming interface, both CAN FD compatible, are included in the delivery.
CAN FD ISO / Non-ISO
Since its first implementations, the CAN FD protocol has evolved and is now included in the ISO 11898-1 standard. This revised version, however, is not compatible with the earlier version of the protocol.
PEAK-System accounts for this situation by supporting both protocol versions in its CAN FD interfaces. Users can therefore switch between ISO and non-ISO modes at any time via software. Products marketed before February 2015 require a firmware update to benefit from this feature. For further information, contact info.peak@hms-networks.com.
D-Sub Pinout
| 2 | CAN-L |
| 3 | GND |
| 6 | GND |
| 7 | CAN-H |
- Expansion card for PCI Express Mini connector (uses one PCIe lane)
- 1, 2 or 4 High Speed CAN buses (ISO 11898-2)
- PCI Express Mini form factor (only for the 1-channel or 2-channel versions, due to the size of the 4-channel version)
- Compliant with CAN 2.0 A/B and FD specifications
- Allows switching between ISO and non-ISO CAN FD protocols
- CAN FD data transfer rate (64 bytes max) from 25 kbit/s to 12 Mbit/s
- CAN transfer rate from 25 kbit/s up to 1 Mbit/s
- Connection to the CAN bus is made via a cable and 9-pin D-Sub connectors (per CiA® 106)
- FPGA implementation of the CAN FD controller
- NXP TJA1044GT CAN transceiver
- Galvanic isolation at the CAN connector up to 300 V, separate for each CAN channel
- CAN termination can be enabled via solder jumpers, separately for each CAN channel
- PCIe data transfer in DMA mode
- DMA memory access operations with 32-bit or 64-bit addressing
- Bus load measurement, including error frames and overload frames at the physical bus level
- Secondary error generation for incoming and outgoing CAN messages
- Extended operating temperature range, from -40 to +85 °C
- PCAN-miniPCIe FD card
- Connection cables with D-Sub connector, 20 or 40 cm as selected. Other lengths available on request
- Drivers for Windows® 11 (x64), 10 (x64) and Linux
- PCAN-View CAN monitor for Windows®
- PCAN-Basic programming interface for applications with CAN connections
- Programming interfaces for standardized automotive protocols
- Manual in PDF format
PEAK-System installation package containing tools and device drivers for our PC interfaces for Windows® 11 (x64/ARM64), 10 (x64). Included tools: PEAK Settings, PCAN-View, PLIN-View Pro and Virtual PCAN-Gateway. Included APIs: PCAN-Basic, PLIN-API and PCAN-RP1210.
Device driver for PEAK CAN interfaces, from kernel 2.6 onward.
Software for viewing, transmitting and recording CAN and CAN FD data traffic for Windows® 11 (x64/ARM64), 10 (x86/x64). Note: PCAN-View is installed together with our device driver.
API for developing applications with CAN CC, CAN FD and CAN XL connections for Windows® 11 (x64/ARM64), 10 (x64).
API for developing applications on CAN connections for Linux.
The PCAN-Basic.NET assembly is available as a package in the NuGet gallery. Online documentation is available on our website.
API for developing applications to communicate with ECUs using the CAN Calibration Protocol (CCP) for Windows® 11 (x64/ARM64), 10 (x86/x64).
API for developing applications to communicate with ECUs using the Universal Measurement and Calibration Protocol (XCP) for Windows® 11 (x64/ARM64), 10 (x86/x64).
API for transmitting data packets according to the ISO-TP standard (ISO 15765-2) for Windows® 11 (x64/ARM64), 10 (x64).
API for communicating with control units according to UDS (ISO 14229-1) for Windows® 11 (x64/ARM64), 10 (x64).
API for vehicle diagnostics according to OBD-2 (ISO 15765-4) for Windows® 11 (x64/ARM64), 10 (x64).
The Pass-Thru API and connection via Pass-Thru software to PEAK CAN interfaces. The installation for Windows® 11 (x64/ARM64), 10 (x64) includes: interface DLLs, configuration software and PCAN-ISO-TP API. Documentation is included in the download.
CAN and CAN FD board for PCI Express Mini (PCIe) slots
The PCAN-miniPCIe FD is a CAN expansion board in the PCI Express Mini format. Its compact size makes it an ideal solution for connecting embedded systems to up to 4 CAN or CAN FD networks. Galvanic isolation of up to 300 volts separates the computer side from the CAN side. This board is available in single-, dual-, and quad-channel versions.
The CAN FD (Flexible Data rate) standard stands out above all for its increased bandwidth for data transfer. Up to 64 bytes of payload data (versus 8 previously) can be transmitted at a bit rate of up to 12 Mbit/s. CAN FD ensures backward compatibility with the CAN 2.0 A/B standard, allowing CAN FD nodes to be used on an existing CAN network (though the CAN FD extensions cannot be used in this case).
The PCAN-View display software and the PCAN-Basic programming interface, both CAN FD compatible, are included in the delivery.
CAN FD ISO / Non-ISO
Since its first implementations, the CAN FD protocol has evolved and is now included in the ISO 11898-1 standard. This revised version, however, is not compatible with the earlier version of the protocol.
PEAK-System accounts for this situation by supporting both protocol versions in its CAN FD interfaces. Users can therefore switch between ISO and non-ISO modes at any time via software. Products marketed before February 2015 require a firmware update to benefit from this feature. For further information, contact info.peak@hms-networks.com.
D-Sub Pinout
| 2 | CAN-L |
| 3 | GND |
| 6 | GND |
| 7 | CAN-H |
