CAN and CAN FD board for the PCI Express bus
With the PCAN-PCI Express FD board, a PC fitted with PCI Express connectors can communicate with CAN and CAN FD networks. Galvanic isolation of up to 500 volts separates the computer side from the CAN side. Available in single-channel, two-channel and four-channel versions.
The CAN FD (Flexible Data rate) standard is essentially characterized by increased transfer capacity. Each frame can contain up to 64 bytes of data (compared with 8 previously), transmitted at bit rates of up to 12 Mbit/s. Backward compatible with the CAN 2.0 A/B standard, CAN FD allows CAN FD nodes to be inserted into an existing CAN network (although the CAN FD extensions remain inoperative in this case).
The PCAN-View monitor and the PCAN-Basic programming interface, intended for developing applications communicating over the CAN bus, are included in the delivery and support the CAN FD standard.
CAN FD ISO / Non-ISO
The CAN FD protocol has evolved since its first implementations and is now part of the ISO 11898-1 standard. This revised version, however, is not compatible with the original protocol.
PEAK-System addresses this constraint by supporting both versions of the protocol on its CAN FD interfaces. Users can thus switch between ISO and Non-ISO modes via software depending on their environment. Devices delivered before February 2015 require a firmware update to benefit from this capability. For any questions or further information, contact info.peak@hms-networks.com.
D-Sub Description
| 1 | Not connected / Optional +5 V |
| 2 | CAN-L |
| 3 | GND |
| 6 | GND |
| 7 | CAN-H |
- PC expansion card for PCI Express connector (PCIe x1)
- 1, 2 or 4 High Speed CAN buses (ISO 11898-2)
- Compliant with CAN 2.0 A/B and FD specifications
- Allows switching between the ISO and non-ISO CAN FD protocols
- CAN FD data transfer rate (64 bytes max) ranging from 25 kbit/s to 12 Mbit/s
- CAN transfer rate from 25 kbit/s up to 1 Mbit/s
- Connection to the CAN bus via 9-pin D-Sub connector (according to CiA® 106)
- FPGA implementation of the CAN FD controller
- NXP TJA1044GT CAN transceiver
- Galvanic isolation at the CAN connector up to 500 V, separate for each CAN channel
- CAN termination can be activated by soldered jumpers, separately for each CAN channel
- PCIe data transfer in DMA mode
- DMA memory access operations with 32-bit or 64-bit addressing
- Bus load measurement, including error frames and overload frames at the physical bus level
- Secondary error generation for incoming and outgoing CAN messages
- Possibility of connecting a 5-volt power supply at the CAN connection via a soldered jumper, e.g. for an external converter
- Extended operating temperature range, from -40 to +85 °C
- PCAN-PCI Express FD card
- Slot bracket equipped with D-Sub connectors for connection to the CAN bus (only for the four-channel version)
- Drivers for Windows® 11 (x64), 10 (x64) and Linux
- PCAN-View CAN monitor for Windows®
- PCAN-Basic programming interface for applications with CAN connections
- Programming interfaces for standardized protocols in the automotive sector
- Manual in PDF format
PEAK-System installation package containing tools and device drivers for our PC interfaces for Windows® 11 (x64/ARM64), 10 (x64). Tools included: PEAK Settings, PCAN-View, PLIN-View Pro and Virtual PCAN-Gateway. APIs included: PCAN-Basic, PLIN-API and PCAN-RP1210.
Device driver for PEAK CAN interfaces from kernel 2.6 onward.
Software for viewing, transmitting and recording CAN and CAN FD data traffic for Windows® 11 (x64/ARM64), 10 (x86/x64). Note: PCAN-View is installed together with our device driver.
API for developing applications with classic CAN, CAN FD and CAN XL connections for Windows® 11 (x64/ARM64), 10 (x64).
API for developing applications on CAN connections for Linux.
The PCAN-Basic.NET assembly is available as a package in the NuGet Gallery. Online documentation is available on our website.
API for developing applications for communication with control units using the CAN Calibration Protocol (CCP) for Windows® 11 (x64/ARM64), 10 (x86/x64).
API for developing applications for communication with control units using the Universal Measurement and Calibration Protocol (XCP) for Windows® 11 (x64/ARM64), 10 (x86/x64).
API for transmitting data packets according to the ISO-TP standard (ISO 15765-2) for Windows® 11 (x64/ARM64), 10 (x64).
API for communicating with control units according to UDS (ISO 14229-1) for Windows® 11 (x64/ARM64), 10 (x64).
API for vehicle diagnostics according to OBD-2 (ISO 15765-4) for Windows® 11 (x64/ARM64), 10 (x64).
The Pass-Thru API and connection via the Pass-Thru software to PEAK CAN interfaces. The installation for Windows® 11 (x64/ARM64), 10 (x64) includes: interface DLLs, configuration software and PCAN-ISO-TP API. Documentation is included in the download.
CAN and CAN FD board for the PCI Express bus
With the PCAN-PCI Express FD board, a PC fitted with PCI Express connectors can communicate with CAN and CAN FD networks. Galvanic isolation of up to 500 volts separates the computer side from the CAN side. Available in single-channel, two-channel and four-channel versions.
The CAN FD (Flexible Data rate) standard is essentially characterized by increased transfer capacity. Each frame can contain up to 64 bytes of data (compared with 8 previously), transmitted at bit rates of up to 12 Mbit/s. Backward compatible with the CAN 2.0 A/B standard, CAN FD allows CAN FD nodes to be inserted into an existing CAN network (although the CAN FD extensions remain inoperative in this case).
The PCAN-View monitor and the PCAN-Basic programming interface, intended for developing applications communicating over the CAN bus, are included in the delivery and support the CAN FD standard.
CAN FD ISO / Non-ISO
The CAN FD protocol has evolved since its first implementations and is now part of the ISO 11898-1 standard. This revised version, however, is not compatible with the original protocol.
PEAK-System addresses this constraint by supporting both versions of the protocol on its CAN FD interfaces. Users can thus switch between ISO and Non-ISO modes via software depending on their environment. Devices delivered before February 2015 require a firmware update to benefit from this capability. For any questions or further information, contact info.peak@hms-networks.com.
D-Sub Description
| 1 | Not connected / Optional +5 V |
| 2 | CAN-L |
| 3 | GND |
| 6 | GND |
| 7 | CAN-H |
