CAN and CAN FD interface for High-Speed USB 2.0
The PCAN-USB FD CAN FD adapter connects CAN FD and CAN networks to a computer via USB. Galvanic isolation up to 500 volts protects the PC from the CAN bus. Its intuitive handling and compact plastic housing make it a tool perfectly suited to fieldwork.
The CAN FD (CAN with Flexible Data rate) standard is distinguished above all by increased bandwidth for data transfer. Each CAN FD frame can carry up to 64 bytes of data (compared to 8 previously) at bit rates of up to 12 Mbit/s. Backward compatible with the CAN 2.0 A/B standard, CAN FD allows CAN FD nodes to be integrated into existing CAN networks. However, the CAN FD-specific extensions cannot then be used.
The PCAN-View monitoring software as well as the PCAN-Basic programming interface, dedicated to developing applications that communicate over the CAN bus, are included in the delivery and support the CAN FD standard.
ISO / Non-ISO CAN FD
Since its earliest implementations, the CAN FD protocol has been improved and is now included in the ISO 11898-1 standard. This revised version of CAN FD is not compatible with the original protocol.
PEAK-System addresses this constraint by supporting both versions of the protocol on its CAN FD interfaces. Users can thus switch by software between "Non-ISO" mode and "ISO" mode depending on the environment used. Devices delivered before February 2015 require a firmware update to benefit from this feature. For further information, contact info.peak@hms-networks.com.
Pin assignment D-Sub
| 1 | not connected / optional +5 V |
| 2 | CAN-L |
| 3 | GND |
| 6 | GND |
| 7 | CAN-H |
- Board with integrated PCAN-MicroMod FD
- CAN bus connection via 9-pin D-Sub connector (according to CiA® 106)
- Screw connectors for all I/O
- Switchable 120 Ohm CAN termination
- Pick-offs for all PCAN-MicroMod FD pins
- "Low Side" power switches for digital outputs
- DIP switches for toggling digital input states
- Protected digital inputs
- LEDs for digital inputs and outputs
- 4 potentiometers for analog inputs
- Solder pads for additional individual wiring
- RS-232 connection with V.24 signal levels for direct access to the microcontroller
- 4-bit rotary coding switch for setting the module ID
- Firmware loading via CAN, USB or RS-232; switchable via 3 buttons
- Reset button to restart the board
- 5 V power supply via Micro-USB or coaxial connector
- Operating temperature range 0 to 70 °C
- Board format 100 x 102 mm with rubber feet
- PCAN-MicroMod FD
- PCAN-MicroMod FD evaluation board
- PCAN-USB FD CAN interface
- 2 m of CAN cable with terminations
- USB connection cable
- PCAN-MicroMod FD Configuration software for Windows®
- CANopen license for one PCAN-MicroMod FD
- Windows® development package with GCC ARM Embedded, flash program and examples
- Manual and wiring diagram (PDF)
Configuration software for PCAN-MicroMod FD products for Windows® 11 (x64/ARM64), 10 (x64).
Easy-to-use tool for updating the firmware of PEAK-System hardware products and CAN and LIN adapters for Windows® 11 (x64/ARM64), 10 (x64).
Package with CANopen EDS files for PCAN-MicroMod FD products.
Firmware development package for Windows®11 (x64), 10 (x86/x64) with GCC ARM Embedded, PEAK-Flash, programming examples and quick start guide. Supported products: PCAN-MicroMod FD, PCAN-GPS, PCAN-GPS FD, PCAN-Router, PCAN-Router DR, PCAN-Router FD, PCAN-Router Pro, PCAN-Router Pro FD, PCAN-RS-232 and PCAN-RS-232 FD.
This package contains library files (Altium Designer file formats) that can be used for simplified integration of the PCAN-MicroMod FD into your own PCB designs.
CAN and CAN FD interface for High-Speed USB 2.0
The PCAN-USB FD CAN FD adapter connects CAN FD and CAN networks to a computer via USB. Galvanic isolation up to 500 volts protects the PC from the CAN bus. Its intuitive handling and compact plastic housing make it a tool perfectly suited to fieldwork.
The CAN FD (CAN with Flexible Data rate) standard is distinguished above all by increased bandwidth for data transfer. Each CAN FD frame can carry up to 64 bytes of data (compared to 8 previously) at bit rates of up to 12 Mbit/s. Backward compatible with the CAN 2.0 A/B standard, CAN FD allows CAN FD nodes to be integrated into existing CAN networks. However, the CAN FD-specific extensions cannot then be used.
The PCAN-View monitoring software as well as the PCAN-Basic programming interface, dedicated to developing applications that communicate over the CAN bus, are included in the delivery and support the CAN FD standard.
ISO / Non-ISO CAN FD
Since its earliest implementations, the CAN FD protocol has been improved and is now included in the ISO 11898-1 standard. This revised version of CAN FD is not compatible with the original protocol.
PEAK-System addresses this constraint by supporting both versions of the protocol on its CAN FD interfaces. Users can thus switch by software between "Non-ISO" mode and "ISO" mode depending on the environment used. Devices delivered before February 2015 require a firmware update to benefit from this feature. For further information, contact info.peak@hms-networks.com.
Pin assignment D-Sub
| 1 | not connected / optional +5 V |
| 2 | CAN-L |
| 3 | GND |
| 6 | GND |
| 7 | CAN-H |
