CAN repeater with 4 kV DC/3.5 kV AC galvanic isolation
The Ixxat CAN-CR220 repeater with two CAN interfaces offers galvanic isolation of up to 4 kV DC/3.5 kV AC for 1 second, strengthening the protection of network segments. It improves CAN bus load capacity, establishes a physical coupling of bus systems and offers the flexibility to optimize network structures. The CAN-CR220 complies with DIN/EN 50178 standards.
Key points
- Robust industrial use — Designed for industrial environments, meeting high requirements for robustness, temperature ranges and safety.
- CAN network design flexibility — Helps optimize CAN network structures by enabling extended topologies (stub lines, star and tree topologies).
- Fast and transparent operation — Minimal impact on real-time behavior, equivalent to a short line length (approx. 40 m/200 ns delay). Transparent transmission, compatible with all higher-layer protocols.
- Savings through simplified wiring — Optimized topologies allow simplified wiring, reducing the number of cables and installation and maintenance costs.
- Increased system protection up to 4 kV DC/3.5 kV AC for 1 s — With the CAN-CR220, network components can be galvanically isolated up to 4 kV DC/3.5 kV AC for 1 second (3.2 kV DC/2 kV AC for 1 minute). This reliably strengthens device protection against electronic damage caused by voltage spikes.
- Network monitoring and fault recovery — In the event of a disturbance, the repeater automatically disconnects the affected segment and reconnects it once the fault has been resolved.
- Built-in bus termination resistors — The built-in bus termination resistors (120 Ohm, switchable via DIP switch) prevent reflections at line ends and ensure optimal communication.
CAN specifications
| CAN mode | High-speed CAN (ISO 11898-2) with CAN choke |
| CAN bit rate | Up to 1 Mbit/s |
| CAN transceiver | TI SN65HVD251 |
General
| Net width (mm) | 100 mm |
| Net height (mm) | 118 mm |
| Net depth (mm) | 22.5 mm |
| Net weight (g) | 137 g |
| Packed width (mm) | 14 mm |
| Packed height (mm) | 4 mm |
| Packed depth (mm) | 18 mm |
| Packed weight (g) | 219 g |
| Mounting | DIN rail mounting (bracket included) |
| Typical consumption at nominal Vcc (mA) | 41 |
| Max. consumption at nominal Vcc (mA) | 100 |
| Supply voltage (V) | +9 V to +32 V DC |
| Isolation | 4 kV DC/3.5 kV AC for 1 sec., 3.2 kV DC/2 kV AC for 1 min. |
| Operating temperature °C min. | -20 °C |
| Operating temperature °C max. | 70 °C |
| Storage temperature °C min. | -40 °C |
| Storage temperature °C max. | 85 °C |
| Relative humidity | 10 to 95 %, no condensation |
| Housing material | Polyamide housing for DIN rail mounting |
| Packaging material | Cardboard |
| Warranty (years) | 1 |
Physical characteristics
| Contains a battery | No |
| Connectors / input / output | 2 x D-Sub 9 connectors, 1 x power connector |
Certifications and standards
| CE | Yes |
| FCC | Yes |
| WEEE category | IT and telecommunications equipment |
| IP rating | IP30 |
- CAN repeater
- user manual
Datasheet
CAN repeater with 4 kV DC/3.5 kV AC galvanic isolation
The Ixxat CAN-CR220 repeater with two CAN interfaces offers galvanic isolation of up to 4 kV DC/3.5 kV AC for 1 second, strengthening the protection of network segments. It improves CAN bus load capacity, establishes a physical coupling of bus systems and offers the flexibility to optimize network structures. The CAN-CR220 complies with DIN/EN 50178 standards.
Key points
- Robust industrial use — Designed for industrial environments, meeting high requirements for robustness, temperature ranges and safety.
- CAN network design flexibility — Helps optimize CAN network structures by enabling extended topologies (stub lines, star and tree topologies).
- Fast and transparent operation — Minimal impact on real-time behavior, equivalent to a short line length (approx. 40 m/200 ns delay). Transparent transmission, compatible with all higher-layer protocols.
- Savings through simplified wiring — Optimized topologies allow simplified wiring, reducing the number of cables and installation and maintenance costs.
- Increased system protection up to 4 kV DC/3.5 kV AC for 1 s — With the CAN-CR220, network components can be galvanically isolated up to 4 kV DC/3.5 kV AC for 1 second (3.2 kV DC/2 kV AC for 1 minute). This reliably strengthens device protection against electronic damage caused by voltage spikes.
- Network monitoring and fault recovery — In the event of a disturbance, the repeater automatically disconnects the affected segment and reconnects it once the fault has been resolved.
- Built-in bus termination resistors — The built-in bus termination resistors (120 Ohm, switchable via DIP switch) prevent reflections at line ends and ensure optimal communication.
